Home | GPS | Special Offers | Deutsch  
- - - - - - - - - - - - - - - - - - - - - - -
Edge 520 | epix | Foretrex 601 | GPSMAP 66 | Montana 700/700i/750i | GPSMAP 276Cx | Camper 780 | Overlander | cfQue 1620 | TracPak | Maps | Accessories | Buyer's Guide | Shopping basketShow shopping basket
Firmware: V6.90 - V6.80 - V6.30 - V6.10 - V5.90 - V5.80 - V5.70 - V5.60 - V5.40 - V5.30 - V5.10 - V5.00 - V4.90 - V4.80 - V4.60 - V4.50 - V4.40 - V4.30 - V3.90 - V3.80 - V3.60 - V3.50 - V3.40 - V3.00 - V2.80 - V2.70 - V2.60 - V2.50 - V2.40 - V2.30

The following lists of changes are based on information provided by GARMIN. Changes or improvements which we consider important or especially useful are shown highlighted.

To view the current firmware version, complete the following steps:

  1. Turn on the GPS.
  2. Press the MENU key twice.
  3. "Setup" is now highlighted, press the ENTER key.
  4. "System" is now highlighted, press "up" and "left" once. "About" should now be highlighted - if not, navigate through the Setup until About is highlighted.
  5. Press the ENTER key.
  6. The system will display the firmware version at the second line ("Software Version") and the unit ID on the third line, followed by various copyright information.
  7. Press the QUIT key to return to the previous page.

Each upgrade replaces the complete firmware in the GPS, which means you need to install only the version you wish to apply. There is no need to install any previous versions.

IMPORTANT: If you upgrade from a version older than V3.40 and are a user of BaseCamp now, or plan to be in the future, you must follow these steps to ensure your data is protected during this software update:

  1. Connect your handheld unit to a computer and launch BaseCamp.
  2. Transfer all tracks, routes and waypoints to BaseCamp.
  3. Delete the /Garmin/GPX folder from the handheld's mass storage.
  4. Update the handheld's software via Web-Updater and reboot the handheld.
  5. Reconnect the handheld to a computer and transfer your data from BaseCamp back to the handheld.

Changes made from version 6.80 to 6.90:

  1. Fixed possible shutdown when viewing depth information on the map.

Firmware Upgrade V6.90 (Please use Web-Updater to install the latest firmware)

To table of contents To table of contents

Changes made from version 6.30 to 6.80:

  1. Added backup of critical data.
  2. Fixed possible route crash.
  3. Fixed adventures not importing from SD cards.

Firmware Upgrade V6.80 (Please use Web-Updater to install the latest firmware)

To table of contents To table of contents

Changes made from version 6.10 to 6.30:

  1. Improved 'Save Portion' track feature. When saving a portion, the device now remembers that position in the track log so it can be used as a track segment for future portion saving.
  2. Fixed possible erroneous track point on power on.
  3. Fixed formatting issue with certain map names in the map information list.

Firmware Upgrade V6.30 (Please use Web-Updater to install the latest firmware)

To table of contents To table of contents

Changes made from version 5.90 to 6.10:

  1. Fixed possible shutdown when scrolling through the waypoints list.

Firmware Upgrade V6.10 (Please use Web-Updater to install the latest firmware)

To table of contents To table of contents

Changes made from version 5.80 to 5.90:

  1. Fixed possible shutdown when reviewing a route in Russian.
  2. Fixed several track distance statistic issues.
  3. Fixed waypoint distances being listed incorrectly for Waypoint Averaging.

Firmware Upgrade V5.90 (Please use Web-Updater to install the latest firmware)

To table of contents To table of contents

Changes made from version 5.70 to 5.80:

  1. Fixed possible issue where BirdsEye satellite imagery would be permanently disabled after booting.

Firmware Upgrade V5.80 (Please use Web-Updater to install the latest firmware)

To table of contents To table of contents

Changes made from version 5.60 to 5.70:

  1. Improved cartography support (Garmin Hunt View maps).
  2. Improved boot time when a large amount of BirdsEye satellite imagery is present.

Firmware Upgrade V5.70 (Please use Web-Updater to install the latest firmware)

To table of contents To table of contents

Changes made from version 5.40 to 5.60:

  1. Fixed issue with barometer when auto calibration is turned off (62s and 62st models).
  2. Fixed issue with power off pressure trending (62s and 62st models).
  3. Fixed missing ascent, descent, and elevation statistics when reviewing certain tracks.
  4. Fixed possible shutdown when displaying the option menu in Czech.

Firmware Upgrade V5.60 (Please use Web-Updater to install the latest firmware)

To table of contents To table of contents

Changes made from version 5.30 to 5.40:

  1. Improved average ascent, average descent, and vertical speed data fields.
  2. Fixed potential shutdown when reviewing a route.
  3. Fixed potential issue when programming a chirp (62s and 62st models).

Firmware Upgrade V5.40 (Please use Web-Updater to install the latest firmware)

To table of contents To table of contents

Changes made from version 5.10 to 5.30:

  1. Added support for additional ActiveRouting cartography.
  2. Improved support for Garmin LakeVu HD cartography.
  3. Improved display of marine-specific lines in BlueChart g2 maps.
  4. Fixed issue retrieving PLSS data in certain TOPO US 24k maps.

Firmware Upgrade V5.30 (Please use Web-Updater to install the latest firmware)

To table of contents To table of contents

Changes made from version 5.00 to 5.10:

  1. Improved pairing behavior with cadence sensors (62s and 62st only).
  2. Fixed potential issue when logging a geocache as found.

Firmware Upgrade V5.10 (Please use Web-Updater to install the latest firmware)

To table of contents To table of contents

Changes made from version 4.90 to 5.00:

  1. Added support for VIRB Remote (62s and 62st models). In the Main Menu press the MENU Key, select "Change Item Order", "Add Page" (at the very bottom) and add the application "VIRB Remote". See TrailTech Software Update, TrailTech Announcement and VIRB for more information.
  2. Added Icelandic keyboard.
  3. Fixed issue with route calculations always avoiding seasonally closed roads.
  4. Fixed possible issue when missing a turn while using the Active Route application.

Firmware Upgrade V5.00 (Please use Web-Updater to install the latest firmware)

To table of contents To table of contents

Changes made from version 4.80 to 4.90:

  1. Added support for additional ActiveRouting cartography.
  2. Fixed issue with incorrect letter capitalization of certain map points.
  3. Fixed issue where wirelessly transmitting a geocache to another device would result in an error message when trying to view the received geocache in BaseCamp.

Firmware Upgrade V4.90 (Please use Web-Updater to install the latest firmware)

To table of contents To table of contents

Changes made from version 4.60 to 4.80:

  1. Improved map performance in densely-populated urban areas.
  2. Fixed trail searching when using multiple active routing maps.
  3. Fixed issue with saving a track's 'show on map' status across a power cycle.
  4. Fixed issue with displaying tracks on the map after performing an area calculation.
  5. Fixed possible issue with searching for an address in cities with extremely long names.
  6. Fixed possible issue with viewing geocache descriptions in night mode.
  7. Fixed minor graphical issue with certain data fields on the map.

Firmware Upgrade V4.80 (Please use Web-Updater to install the latest firmware)

To table of contents To table of contents

Changes made from version 4.50 to 4.60:

  1. Added quick access to the geocaching options from the compass and map pages.
  2. Added 'Geocache Start Page' option to geocache setup page (Setup -> Geocaches ).
  3. Improved ascent and descent calculations.
  4. Fixed potential shutdown when searching for adventures.
  5. Fixed issues with alphabetical sort from waypoint manager.
  6. Fixed potential issues with geocaching dashboard.

Firmware Upgrade V4.60 (Please use Web-Updater to install the latest firmware)

To table of contents To table of contents

Changes made from version 4.40 to 4.50:

  1. Improved map drawing at low zoom levels.
  2. Fixed inability to edit archived tracks.
  3. Fixed ability to use NMEA depth for waypoints and tracks.
  4. Fixed display of geocache coordinates with non-default map datum.
  5. Fixed overlapping position text for right to left languages.
  6. Fixed overlapping position text in data fields.

Firmware Upgrade V4.50 (Please use Web-Updater to install the latest firmware)

To table of contents To table of contents

Changes made from version 4.30 to 4.40:

  1. Added Adventure support with latest version of BaseCamp. See TrailTech for more information.
  2. Added support for new tempe sensor (GPSmap 62s/st only). See TrailTech for more information.

Firmware Upgrade V4.40 (Please use Web-Updater to install the latest firmware)

To table of contents To table of contents

Changes made from version 3.90 to 4.30:

  1. Added new route activity types and improved BaseCamp compatibility. See TrailTech for more information.
  2. Added ability to sort waypoints alphabetically.
  3. Added support for Kenwood NMEA Waypoint Sentence.
  4. Improved GPS response at low speeds.
  5. Fixed issue with preserving routes imported from BaseCamp (identical maps required).
  6. Fixed issue where the map would sometimes not refresh when using the active route page.
  7. Fixed issue with the Glide Ratio data field.
  8. Fixed Spell Search in German.
  9. Fixed possible issue with Where To? > Address searching.

Firmware Upgrade V4.30 (Please use Web-Updater to install the latest firmware)

To table of contents To table of contents

Changes made from version 3.80 to 3.90:

  1. Added symbol filtering to FIND > Waypoints and Waypoint Manager.
  2. Improved GPS response at low speeds.
  3. Fixed daylight saving time issue in Sun and Moon application.
  4. Fixed issue that could occur when restoring map zoom level defaults.
  5. Fixed issues with support for Canada BlueChart g2 maps.

Firmware Upgrade V3.90 (Please use Web-Updater to install the latest firmware)

To table of contents To table of contents

Changes made from version 3.60 to 3.80:

  1. Added Geocaching with Photos, seeGARMIN Blog for details.
  2. Improved elevation data stored in track logs.
  3. Fixed issue with 'Hut' point type in TOPO Australia & New Zealand maps.
  4. Fixed issue with magnetic north offset when projecting a waypoint.

Firmware Upgrade V3.80 (Please use Web-Updater to install the latest firmware)

To table of contents To table of contents

Changes made from version 3.50 to 3.60:

  1. Fixed an issue with the reporting of pressure from the barometric altimeter (GPSMAP 62s/62st only).

Firmware Upgrade V3.60 (Please use Web-Updater to install the latest firmware)

To table of contents To table of contents

Changes made from version 3.40 to 3.50:

  1. Added Photo Viewer application.
  2. Improvements to the geocaching experience. See TrailTech for more information.
  3. Fixed a potential hang on startup when importing large numbers of waypoints, tracks, routes, or geocaches.
  4. Fixed issue with very long geocache descriptions.
  5. Fixed shutdown when reviewing certain geocache descriptions.
  6. Fixed issue where some auto-archived tracks would be named in English regardless of user language.
  7. Fixed bug that could cause some geocaches to not import.
  8. Fixed issue with track log recording while using the stopwatch.
  9. Fixed issue with the anchor drag alarm.
  10. Fixed issue with total ascent and total descent fields not displaying values greater than 9999 meters.
  11. Modified default map trails to appear as dashed red lines.
  12. Fixed potential issue with screenshot color reproduction.

Firmware Upgrade V3.50 (Please use Web-Updater to install the latest firmware)

To table of contents To table of contents

Changes made from version 3.00 to 3.40:

  1. Added support for advanced geocache logging with OpenCaching.com. See TrailTech for more information.
  2. Fixed issue with multilingual custom POI files.
  3. Fixed issue with setting proximity alerts. The unit of measure can be changed by entering the 'Proximity Alarms' page, pressing the 'Menu' key, and selecting 'Change Units'.

Firmware Upgrade V3.40 (Please use Web-Updater to install the latest firmware)

To table of contents To table of contents

Changes made from version 2.80 to 3.00:

  1. Updated magnetic Earth field data.
  2. Improved GPS performance.
  3. Improved support for BirdsEye Satellite ImageryTM (each provider's imagery can be configured independently).
  4. Increased the maximum number of supported JNX files to 250 from 200.
  5. Fixed issues with WAAS/EGNOS.
  6. Fixed issue with track navigation sometimes not adding waypoints to the Active Route list.
  7. Fixed issue with track and route review from the map page if you came from the elevation plot.
  8. Fixed issue with MPC map labels disappearing.
  9. Fixed issue with gpi files that have alerts attached to the points.
  10. Fixed issue with progress bar displaying properly on power up.
  11. Fixed issue with track navigation not adding waypoints to the Active Route list when they are exactly equal to a track point.
  12. Fixed shutdown when unit had more than the maximum number of JNX files on it.
  13. Fixed shutdown related to topographical maps and land cover text size.
  14. Fixed Glide Ratio to Destination field.
  15. Fixed problem with profiles and the fields on the map page.
  16. Fixed an issue with magnetic north reference and waypoint headings.
  17. Fixed shutdown on the map screen when a waypoint was being moved to the same location as a geocache or other POIs.
  18. Fixed issue where proximity waypoint alerts could only be set in feet regardless of what was selected as a Distance/Speed unit in the setup page.
  19. Fixed an issue with archived tracks not displaying properly.
  20. Fixed an issue with having too many custom symbols on the device.
  21. Modified the 'Arriving at Destination' message banner so that it no longer appears when navigating to a geocache.

Firmware Upgrade V3.00 (Please use Web-Updater to install the latest firmware)

To table of contents To table of contents

Changes made from version 2.70 to 2.80:

  1. Fixed shutdown related to the current track that occurred after updating the software.
  2. Fixed a hang that occurred when a unit had 1000 auto-named waypoints.
  3. Fixed issue with marine map points sometimes drawing with the incorrect symbol.

Firmware Upgrade V2.80 (Please use Web-Updater to install the latest firmware)

To table of contents To table of contents

Changes made from version 2.60 to 2.70:

  1. Added support for ChirpTM (see www.garmin.com/chirp).
  2. Fixed problem with certain custom maps.
  3. Fixed problem with certain JPEG images.
  4. Fixed issue with Sight 'N Go and user north reference.

Firmware Upgrade V2.70 (Please use Web-Updater to install the latest firmware)

To table of contents To table of contents

Changes made from version 2.50 to 2.60:

  1. Fixed issue while using spell search in route planner.
  2. Fixed issue where tracks could not be disabled from the map.
  3. Fixed issues with odometer distance.
  4. Fixed shutdown while panning the map for extended periods of time.

Firmware Upgrade V2.60 (Please use Web-Updater to install the latest firmware)

To table of contents To table of contents

Changes made from version 2.40 to 2.50:

  1. Added Automatic Shaded Relief option.
  2. Added display color to track gpx files.
  3. Added import indicator for gpx files.
  4. Added multicaching support.
  5. Added periodic track archiving.
  6. Added track review page improvements.
  7. Improved map selection. Visit http://garmin.blogs.com/softwareupdates/trail-tech for more information.
  8. Improved keyboard responsiveness.
  9. Fixed issues with inconsistent altimeter readings.
  10. Fixed calendar to display all geocache finds and attempts on the correct day.
  11. Fixed occasional shutdowns.
  12. Fixed paging after logging a geocache.
  13. Fixed shutdown on About Page.
  14. Fixed spot sounding display on certain maps.
  15. Updated map review of tracks and routes. The distance shown is now the distance along the route or track.

Firmware Upgrade V2.50 (Please use Web-Updater to install the latest firmware)

To table of contents To table of contents

Changes made from version 2.30 to 2.40:

  1. Improved display of position formats on keyboard page.
  2. Fixed problem with position entry when using Latvian TM position format.
  3. Removed occasional screen glitch when routes are being calculated.
  4. Added Spanner interface option to 62 models (Note by TRAMsoft: Spanner allows to use the USB port with most NMEA 0183 compliant mapping programs by creating a virtual serial port).

Firmware Upgrade V2.40 (Please use Web-Updater to install the latest firmware)

To table of contents To table of contents

Changes made from version 2.10 to 2.30:

  1. Added Geocache filtering. Select Setup -> Geocaches to add custom filters.
  2. Added brightness adjustments for BirdsEye imagery.
  3. Improved WAAS performance.
  4. Fixed intermittent issue with two keyboard input bars appearing on spell search.

Firmware Upgrade V2.30 (Please use Web-Updater to install the latest firmware)

To table of contents To table of contents
GARMIN GPSmap 62 GARMIN GPSmap 62s GARMIN GPSmap 62st Rugged hand held GPS receiver with large color display, integrated base map, auto-routing and USB interface. The GPSmap 62s and 62st are additionally equipped with an electronic compass, a barometrical altimeter, a slot for an optional uSD memory card, a connector for an external antenna and support for wireless communication with compatible devices. The GPSmap 62st comes furthermore with a pre-installed topographic map of Europe, see detailed description.

Home | GPS | Special Offers | Deutsch  

TRAMsoft GmbH
Laettenweg 19 / CH-8335 Hittnau / Switzerland
Contact
Last modification: 11/22/2023 (RA)

(This document was created with TRAMsoft XbCMS V1.3-00, does not require any browser specific features and is compliant with the W3C standard "HTML 4.01 Transitional")